WALTON Primo V1 Flashing Solution With CM2 Dongle

WALTON Primo V1 Flashing Solution With CM2 Dongle

Operation : Flash [ v1.58 ]

Flash

1. Power Off Phone , Remove battery , Insert back

2. Insert USB cable. In some cases require hold BootKey

Wait for phone...

Phone found! [ 17 ]

Sync...

Inital Boot Ok!

BB_CPU_PID : 6592

BB_CPU_NME : [MediaTek] MT6592_S00

BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000

Processing BROM stage

Settings for BROM configured!

SecCfgVal : 0x00000000

BromVer   : 0x00FF

BLVersion : 0x0001

PreLoader : Active [ Boot with PL ]

BootLdrSS : NORMAL with PRELOADER

Processing DA stage

DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07

Sending and initialize DA ...

Running DA ver.4.2 on BBID : 0x8A

NAND Flash : NOT INSTALLED

eMMC Flash : 90014A484147326504050FA1E1493133

Initialize Memory ... 

DRAM already initialized by Preloader

DAgent sent , init HW now

eMMC FlashIC initialized

[eMMC] : FLASH_VEN : 0x90 , OEM : 014A

[eMMC] : FLASH_INF : [HYNIX] , e2GA

[eMMC] : FLASH_CID : 90014A484147326504050FA1E1493133

[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000

[eMMC] : FLASH_LEN : 0x00000003AB800000

[eMMC] : FLASH_UCP : 15032 MiB [eMMC 16 GiB]

DEV RID    : 0xC0BB5E81F044E209CB46D7592F3BF10E

INT RAM    : 0x00020000

EXT RAM    : 0x80000000 [2 GiB]

BOOT TYPE  : EMMC_FLASH_BOOT

SOC VERIFY : C1

Boot Ok!

ScatCFG : BaseBand : MT6592 , Project : tianyu92_wet_jb9 , Storage : EMMC

Setting : Flash Pre-Erase : Off ( Write Flash Only )

Setting : AFF verify :  Enabled

Setting : HW verify :  Enabled

BL : Check HW compatibility

BL : BBID supported by BootLoader!

BL : Check eMMC compatibility

BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3855 mV

BL : BatteryLevel Ok

SecCfg Passed , 1799

BMT remark not need. Will skip

Sending Preloader ... 

Use : preloader_tianyu92_wet_jb9.bin

Preloader Sent , Init passed

SecCfg Passed , 1799

PartCount : 0014

Update PMT by user request

Repartition Done!

Use FLN Mode

Processing : Flash Write

Flash now : MBR

Image Flash Ok

Flash now : EBR1

Image Flash Ok

Flash now : UBOOT

Image Flash Ok

Flash now : BOOTIMG

Image Flash Ok

Flash now : RECOVERY

Image Flash Ok

Flash now : SEC_RO

Image Flash Ok

Flash now : LOGO

Image Flash Ok

Flash now : EBR2

Image Flash Ok

Flash now : ANDROID

Image Flash Ok

Flash now : CACHE

Image Flash Ok

Flash now : USRDATA

Image Flash Ok

Flash Write Done, time used : 00:02:45

Processing : Verify

Verify Passed : MBR

Verify Passed : EBR1

Verify Passed : UBOOT

Verify Passed : BOOTIMG

Verify Passed : RECOVERY

Verify Passed : SEC_RO

Verify Passed : LOGO

Verify Passed : EBR2

Verify Passed : ANDROID

Verify Passed : CACHE

Verify Passed : USRDATA

Data Verify Done, time used : 00:00:15

Update Mirror PMT

Update Done!

Update RomInfo done

Done!

Elapsed: 00:03:31

Reconnect Power/Cable!