Qmobile X32 Reset Solution With CM2 Dongle

Qmobile X32 Reset Solution With CM2 Dongle

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back

2. Insert USB cable. In some cases require hold BootKey

Wait for phone...

Phone found! [ 9 ]

Sync...

Inital Boot Ok!

BB_CPU_PID : 6580

BB_CPU_NME : [MediaTek] MT6580_S00

BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000

Processing BROM stage

Settings for BROM configured!

SecCfgVal : 0x00000000

BromVer   : 0x00FF

BLVersion : 0x0001

PreLoader : Active [ Boot with PL ]

BootLdrSS : NORMAL with PRELOADER

Processing DA stage

DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07

Sending and initialize DA ...

Running DA ver.4.2 on BBID : 0x94

NAND Flash : NOT INSTALLED

eMMC Flash : 88010345504131303022AC570141C2B9

Initialize Memory ... 

DRAM already initialized by Preloader

DAgent sent , init HW now

eMMC FlashIC initialized

[eMMC] : FLASH_VEN : 0x88 , OEM : 0103

[eMMC] : FLASH_INF : [FORESEE] , 001AP

[eMMC] : FLASH_CID : 88010345504131303022AC570141C2B9

[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000

[eMMC] : FLASH_LEN : 0x00000001CE100000

[eMMC] : FLASH_UCP : 7393 MiB [eMMC 8 GiB]

DEV RID    : 0xD5229C25A090694E727A1708B344FFCB

INT RAM    : 0x00020000

EXT RAM    : 0x20000000 [512 MiB]

BOOT TYPE  : EMMC_FLASH_BOOT

SOC VERIFY : C1

Boot Ok!

[AP] : Initial info read Ok!

Brand     : QMobile

ProdName  : X32

ProdModel : QMobile X32

Device    : X32

AndroidVer: 6.0

MTKxCPU   : MT6580

MTKxPRJ   : ALPS.W10.24.p0

SECURITY : 

IMEI_SW [1] : 358834070080114

IMEI_SW [2] : 358834075080119

BTMAC Addr  : BC4434DFEC14

WiFi MAC    : BC4434DFC40A

Done!

Elapsed: 00:00:07

Reconnect Power/Cable!

Operation : Clear UserLocks [Pin/Pwd/Pattern/FVLock/GoogleAcc] [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back

2. Insert USB cable. In some cases require hold BootKey

Wait for phone...

Phone found! [ 9 ]

Sync...

Inital Boot Ok!

BB_CPU_PID : 6580

BB_CPU_NME : [MediaTek] MT6580_S00

BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000

Processing BROM stage

Settings for BROM configured!

SecCfgVal : 0x00000000

BromVer   : 0x00FF

BLVersion : 0x0001

PreLoader : Active [ Boot with PL ]

BootLdrSS : NORMAL with PRELOADER

Processing DA stage

DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07

Sending and initialize DA ...

Running DA ver.4.2 on BBID : 0x94

NAND Flash : NOT INSTALLED

eMMC Flash : 88010345504131303022AC570141C2B9

Initialize Memory ... 

DRAM already initialized by Preloader

DAgent sent , init HW now

eMMC FlashIC initialized

[eMMC] : FLASH_VEN : 0x88 , OEM : 0103

[eMMC] : FLASH_INF : [FORESEE] , 001AP

[eMMC] : FLASH_CID : 88010345504131303022AC570141C2B9

[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000

[eMMC] : FLASH_LEN : 0x00000001CE100000

[eMMC] : FLASH_UCP : 7393 MiB [eMMC 8 GiB]

DEV RID    : 0xD5229C25A090694E727A1708B344FFCB

INT RAM    : 0x00020000

EXT RAM    : 0x20000000 [512 MiB]

BOOT TYPE  : EMMC_FLASH_BOOT

SOC VERIFY : C1

Boot Ok!

LSSDB Ok!

LSSWL Ok!

LSSSH Ok!

LSSNG Ok!

LSSNP Ok!

Security Settings : Clear Ok!

[Info] : That feature NOT RESET "PRIVACY PASSWORD LOCK"! Use separate button!

[Info] : That feature NOT RESET "FRP/GoogleLOCK"! Use separate "FRP" reset!

[Info] : If phone stuck on "Logo" : 

1. Wait 2-3 minutes. Power Off phone by long press "Power" button

2. Power On phone again

3. Or wait up to 3-7 minutes, until phone start by itself

4. Also recommended reboot phone twice before start use it

Done!

Elapsed: 00:00:21

Reconnect Power/Cable!